Pool Equipment Installations in West Palm Beach, FL
Our pool equipment installation in West Palm Beach covers pumps, heaters, filters and lights, sized to your pool and installed to manufacturer spec. The quote is free, and we’ll tell you if a repair makes more sense.
Pool Equipment Replacement and Upgrades in West Palm Beach
Most people call us about installation because something died, not because they planned an upgrade. That’s fine. It’s also worth knowing that the replacement you end up with is often better than what failed.
Pool equipment installation here covers pumps, heaters, filters and lights. We’re licensed and factory trained on Hayward, Pentair, Jandy and Zodiac, so the work is done to manufacturer spec and to code. That matters more than it sounds on anything with gas or electrical, and it’s what keeps a warranty valid.
Equipment in South Florida runs most of the year rather than four or five months, so it wears out faster than the manufacturer averages assume. The upside is that an efficient pump or heater pays back faster here, because it’s running more hours. And if you’d like the whole pad looked after once it’s in, our pool service in West Palm Beach covers that too.
Pool Filter Installation
Cartridge, sand and DE.
The one thing worth getting right is size. An undersized filter runs at higher pressure, clogs faster and makes your pump work harder for the rest of its life. Plenty of pools around here were built with whatever filter was cheapest at the time. We size it to your water volume and your actual flow rate instead.
If you’re choosing between types, cartridge is the easiest to live with and needs no backwashing, so it wastes no water. Sand is cheapest up front. DE filters the finest but takes the most work.
Pool Heater Installation
Gas heaters, electric heaters and heat pumps.
For a pool in this climate, a heat pump is usually the right answer. It costs more to install and far less to run, and our winters never get cold enough to push it out of its efficient range. That’s the thing that makes heat pumps a poor fit further north.
Gas earns its place on a spa. If you want hot water in twenty minutes, a heat pump won’t do that and gas will. So plenty of setups here run a heat pump on the pool and gas on the spa.
Variable Speed Pool Pump Installation
If your single speed pump dies, you’re getting a variable speed one whether you planned to or not. Federal efficiency rules that took effect in July 2021 changed what can be sold for most inground pools, so this isn’t an upsell. It’s the shelf.
The good news is that it’s the one upgrade that actually pays for itself. A pump uses far less power at half speed than at full, much more than the halving you’d expect. So running longer and slower filters the same water for a fraction of the electricity. Pair it with pool automation installation and the schedule stays set correctly.
They’re also much quieter, which people notice more than they expect if the pad sits near a bedroom window.
Pool Light Installation and LED Replacement
The question we get asked most about lights: no, we don’t have to drain your pool. The fixture pulls out of its niche on enough cord to sit on the deck, and the work happens up there. People assume it’s a major job, and it usually isn’t.
If you still have an old incandescent light, an LED cuts the power draw to a fraction and lasts years instead of months. Color changing LEDs are the common upgrade now, and they’re worth it if you use the pool in the evening. We handle new light installation and LED replacement in existing niches.
Pool Equipment Installation Cost
In our area, a variable-speed pump typically runs $1,500 to $2,800 installed. A gas heater is roughly $2,000 to $4,000 and a heat pump about $3,000 to $7,500, while a new filter usually lands between $300 and $1,000.
Prices move with the equipment, so we quote after we’ve looked at the pad. What drives the number is the size of your pool, what’s already there, whether the plumbing and electrical need rework, and how much room there is to reach the equipment.
A straight swap onto existing plumbing is a different job from a pad that needs repiping. Be suspicious of anyone who quotes the same for both without seeing it.
We’ll also tell you when not to replace something. If your pump has ten good years in it and only the capacitor has gone, we’d rather fix it and come back in a decade.
The quote is free. Call (561) 567-0822.
When New Equipment Isn't the Whole Job
New equipment runs best on clean water with a filter that isn’t fighting it. And sometimes a repair or a specialty fix is all the pad needs.
Pool Cleaning
Weekly pool service, pool filter cleaning, spa cleaning and pool tile cleaning keep new equipment from working harder than it should.
Pool Repairs
Not every failure means new equipment. We handle pool pump repair, pool heater repair, pool filter repair and spa repair on Hayward, Pentair, Jandy and Zodiac equipment.
Pool Service
One company for the whole pool: weekly cleaning, water care, repairs and the new equipment you just put in.
Specialty Services
Upgrades like pool automation and salt systems pair well with a new pump. We also handle acid wash, green to clean and sand changes.
Our Service Area Across Palm Beach County
We install equipment on pools from Juno Beach and Jupiter down to Greenacres and Boynton Beach. Each town below has its own page, or you can see all of our service areas.
Pool Equipment Installation Questions We Hear Most
Here’s what homeowners ask before they replace a pump, heater, filter or light. Don’t see yours? Call (561) 567-0822.
Costs, Lifespan and Choosing an Installer
A variable-speed pump typically runs $1,500 to $2,800 installed, a gas heater about $2,000 to $4,000 and a heat pump about $3,000 to $7,500. A new filter is usually $300 to $1,000. Simple Pool Care quotes free after seeing the pad.
Not as long as the brochures say, because it runs most of the year. A pump is often due for replacement around 7 to 10 years and a filter tank around 8 to 12. Heat pumps tend to outlast gas heaters. Salt air and hard water shorten all of it.
Usually by a lot. A pump draws far less power at low speed, so running slower for longer filters the same water for a fraction of the electricity. For most West Palm Beach pools, that's roughly $600 to $1,200 a year.
Ask for the exact make and model, and whether it's sized to your pool's gallons and flow rate. Then ask whether the price covers plumbing changes and electrical work, and who registers the warranty. We install everything to manufacturer spec so the warranty stays valid.
Simple Pool Care installs equipment as a licensed and insured, owner-operated company in West Palm Beach, rated 5.0 on Google. Our technicians are factory trained on Hayward, Pentair, Jandy and Zodiac. We size equipment to your pool, not to the cheapest option, and the quote is free.
Pumps, Heaters, Filters and Lights
For the pool, a heat pump. It costs more up front but runs at roughly $100 to $200 a month, against $200 to $400 for gas, because it pulls heat from our warm air. Gas still makes sense on a spa, where you want hot water in twenty minutes.
In practice, for most inground pools, yes. Federal efficiency rules from July 2021 make it hard for most single-speed pumps of one horsepower and up to qualify. So if your old pump dies, the replacement will almost always be variable speed.
One sized to your pool, not the biggest one on the shelf. We work from the water volume, the pipe size and the flow your filter and heater need. An oversized pump pushes water through the filter too fast and wastes power.
Cartridge is the easiest to live with and needs no backwashing, so it wastes no water. Sand costs the least up front. DE filters the finest but takes the most work. Whichever you pick, size matters more than type.
No. The fixture comes out of its niche on enough cord to reach the deck, and the work happens up there. Swapping an old incandescent bulb for an LED cuts the power draw sharply and lasts far longer.
Still have questions?