Spa Repair and Hot Tub Repair in West Palm Beach, FL

Spa repair and hot tub repair in West Palm Beach for heaters, pumps, jets, leaks and breaker trips. We find the real fault and quote it before any work starts, on attached spas and standalone tubs.

Google, Yelp and Facebook five-star review badges
Schedule Service!
Google, Yelp and Facebook five-star review badges
Name
Address

Hot Tub Repair for a Cold Spa, Weak Jets or a Tripped Breaker

You sit down for an evening soak and the water is lukewarm. Or the jets barely push, or the topside panel is flashing a code you’ve never seen. Most of our spa calls start like that. Most of them also trace back to a short list of parts.

Our spa repair work covers the heater, the jet pumps and blower, the jets and plumbing, the circulation, and the controls and wiring. That includes spas built into the pool and standalone hot tubs out on the lanai. Our factory training covers Hayward, Pentair, Jandy and Zodiac, which is most of what sits on equipment pads around here.

Spa equipment has a harder life than pool equipment. The water runs hot, often close to 104 degrees, and there’s only a fraction of a pool’s volume. So every bather and every swing in the chemistry hits harder. That’s why a spa usually shows a problem before the pool does.

We diagnose before we quote. We also won’t swap a whole heater or pump when a sensor, seal or capacitor will do. Spa repair is part of our pool repairs work, so the tech at your spa can look over the rest of the pad too.

If the spa keeps tripping its breaker or GFCI, stop resetting it and leave it off until it’s checked. That trip is a safety device doing its job. Call (561) 567-0822 or request a quote, and tell us what the spa is doing.

Underwater close-up of a working spa jet pushing bubbles through hot tub water
Book Spa Repair in West Palm Beach

Spa Repair for Heaters, Pumps, Jets and Controls

Most spa repairs fall into six groups. Here’s what usually fails in each one, and what we check before we name a part.

SymptomCommon causesWhat we check
Spa won’t heat or heats slowlyLow flow, a scaled element, a failed sensor or high-limit switchFilter, valves, flow or pressure switch, element, sensors
Weak or dead jetsClogged filter, suction air leak, diverter valve, failing pumpPump basket, suction side, valves, jet inserts
Pump hums or won’t startFailed capacitor, jammed impeller, worn bearingsCapacitor, impeller, bearings, voltage
GFCI or breaker tripsShorted element, wet motor or blower, wiring faultHeater circuit, motors, control box, bonding
Water lossShaft seal, unions, heater fittings, jet bodiesPressure test and dye test at the fittings
Error code or dead panelSensor fault, failed board, loose or wet connectionCodes, sensors, board, connections

Spa Heater Not Heating

A spa that won’t heat is the call we get most, and the heater itself is often fine. Gas heaters and heat pumps won’t fire without enough water moving through them. So a dirty filter, a closed valve or a bypass set wrong shuts them down on low flow. Electric spa heaters use an element that can scale over or burn out. A bad temperature sensor, flow switch or high-limit switch leaves you with the same cold water.

When a heater cycles on and off before the spa reaches temperature, look at flow first. The usual causes are a dirty filter, a closed valve or an external bypass out of adjustment. After that come a pressure switch out of adjustment and a thermostat out of calibration. On shared equipment, the fault can sit on the pool side, and that’s where our pool heater repair work picks up.

Two warnings on gas heaters. Never run one that has been under water, which matters here after a storm floods an equipment pad. And if a propane heater fails to light, the unburned gas sinks to the bottom of the cabinet because it’s heavier than air. So repeated restart attempts are a job for a technician.

Jet Pump Humming, Leaking or Running Hot

A jet pump that hums but won’t turn usually has a failed start capacitor or debris jammed in the impeller. Grinding or screeching points to worn bearings. Water dripping where the motor meets the pump is the shaft seal. Fix it before the leak reaches the motor bearings.

Spa jet pump motors are made for short run times, so they don’t tolerate heat the way a pool motor does. Packed into a hot tub cabinet or a closed box with no airflow, they run hot and trip their thermal overload. Most pull outside air through for cooling, too. That’s why leaves, dust and grass clippings in the vents shorten their life.

The air blower, if you have one, is its own small air pump. Water must never reach the blower motor. So the air line uses a check valve or a loop of pipe that rises above the water level. When that protection fails, the blower trips the breaker or seizes.

Weak or Dead Jets

Weak jets are usually a flow problem, not a jet problem. A loaded filter, a clogged pump basket, low water or a suction leak starves the pump. You’ll hear it change pitch as it cavitates. Left that way, cavitation can damage both the pump and the motor.

Once the flow checks out, we move to the diverter valves, air controls and jet inserts, where scale and debris collect. If the pump keeps losing prime, air is getting in on the suction side. The strainer lid O-ring and the first fitting into the pump are the usual spots.

Leaks Around the Equipment or Shell

Spa leaks show up at pump shaft seals, unions, heater connections, jet bodies and the plumbing under a hot tub cabinet. We pressure test the lines and use dye at the fittings to find where the water is going. Then we repair that spot instead of patching around it.

You can check whether it’s a leak at all. Hot water evaporates faster than cool water, so test with the cover on and the jets off. Mark the level, then look again after 24 hours. A clear drop is worth a call, because a slow leak can leave a pump or heater short of water.

Flashing Error Codes or a Dead Topside Panel

A flashing code is the control board telling you which sensor or circuit it doesn’t like. Flow, temperature and high-limit codes usually lead back to the heater circuit. A dead panel can be a failed board, a loose connection or moisture in the control box. If the spa runs off pool automation, we check that side too.

A GFCI That Keeps Tripping

A GFCI cuts the power when it senses about 5 milliamps leaking out of the circuit. That limits how long a shock can last. So a GFCI that keeps tripping is protecting someone. The usual causes are a shorted heater element, a wet pump or blower motor, moisture in the control box, or a wiring or bonding fault.

Spa wiring falls under Article 680 of the National Electrical Code. Electrical repairs should only be done by qualified, licensed people. Older spas may have no GFCI protection at all, because the code’s GFCI rule for spas only took effect in 1981. If yours has none, that’s worth fixing even if nothing has failed yet.

Why Spa Equipment Fails Faster Than Pool Equipment

Heat and volume. Almost every spa repair we do traces back to one or both. They’re worth understanding, because they decide how long a spa heater or pump lasts.

Hot Water Pushes Calcium Out

Warm water holds less calcium than cool water. So spa water at 102 or 104 degrees drops scale far more readily than pool water at 82. The surfaces inside the heater run hotter still, and that’s why scale forms there first. It narrows the passages and cuts heat transfer, and the flow drops until the heater starts to fault.

That’s why spa calcium should run lower than a pool’s, ideally around 150 to 250 ppm. It’s also why a scale inhibitor is common in spa water. Our hard water makes this a real fight in Palm Beach County. Keeping the water balanced does more for heater life than any part we can sell you.

A Small Body of Water Takes a Heavy Load

A pool usually gives each swimmer about 1,800 gallons of water. A spa often gives each person around 200. So the sweat, body oil, lotion and sunscreen people bring in end up far more concentrated. Hot water also burns through sanitizer faster. Those oils coat filters and heater surfaces, and they feed bacteria whenever the sanitizer runs low.

It’s also why sand filters are a poor match for spas. Body oils and scale can coat the sand in a clay-like layer until it stops filtering and starts blocking flow. Degreasing helps, but once the sand is coated, it has to be replaced. On cartridge spas, a torn element lets debris straight through to the heater and jets. That’s a pool filter repair job before it becomes a heater job.

Jets and Air Push the pH Up

Jets and the blower stir air through the water, and that strips out carbon dioxide. The result is pH creeping up while alkalinity falls. Bromine, which many spas use, is acidic and pulls pH the other way. So spa pH swings in both directions. When it sits wrong, the water either scales the heater or starts eating the metal in it. We keep it between 7.4 and 7.6.

Old Water Turns Corrosive

Spa water keeps every mineral and dissolved solid that has ever gone into it. Evaporation in the heat concentrates them further. As total dissolved solids climb, the sanitizer works less well and the water turns dull. The water can also start corroding heater elements and staining metal. That’s galvanic corrosion, and it’s one of the quieter reasons a spa heater fails early.

How Often to Drain a Spa to Prevent Repairs

Most people drain a spa twice a year because it feels about right. There’s an actual formula for it, and it usually says more often than that.

How often a spa needs fresh water depends on how hard it gets used. Our spa cleaning page walks through the math. As a rough guide, a 350-gallon spa with four regular users needs new water in under 30 days.

If you’d rather test than calculate, change the water once total dissolved solids rise about 1,500 ppm above the reading at fill. Foam that won’t clear, a stale smell or cloudy water that won’t polish up are signs it’s due as well.

One caution for inground spas: where the water table is high, as it is along much of our coast, groundwater can lift an empty shell. Check that the hydrostatic relief valve works before you drain it, or call us first.

Draining on schedule is part of regular spa maintenance, and it costs far less than a heater. Water that never gets changed coats the heater, the jets and the seals with everything that has been in it. That’s where a lot of spa repair work starts.

Safety Limits on Spa Temperature and Suction

Some spa faults are comfort problems. These two are safety problems, so they come first on any spa repair call.

104 Degrees Is the Ceiling

Spa water should never run above 104°F. That limit comes from federal consumer safety work on spa temperature controls. The CDC’s guidance for hot tub users says the same, and some local codes cap it at 102. If a spa runs hotter than its setting, that’s a thermostat, sensor or high-limit fault. It needs fixing before anyone gets in.

Even at the right temperature, long soaks can overheat the body. The usual advice is 10 to 15 minutes at a time, then out to cool down.

Suction Covers on Spa Drains

Spas are shallow and their suction is strong, so they’re where most hair and body entrapment incidents happen. Drain covers crack and wear out, and a replacement has to be a certified anti-entrapment cover. Check them through the year. Make sure everyone knows where the pump’s shutoff switch is, too.

When we replace a spa pump motor, the new one has to match the old motor’s total horsepower. A bigger motor raises the entrapment risk, while a smaller one won’t move enough water through the heater and filter.

Attached Spa or Standalone Hot Tub Repair

The two setups fail in different ways, so it’s the first thing we ask when you book a spa repair.

Attached Spas Share the Pool's Equipment

Many spas in Palm Beach County are built into the pool. They share its pump, filter, heater and plumbing, with valves that switch the water between the two. So a cold spa can turn out to be a heater fault on the pool side. It can also be a pump that has lost prime, which is pool pump repair territory. A raised spa that drains into the pool overnight usually points to a valve or check valve. We look at the whole system before we blame the spa.

Standalone Hot Tubs on the Lanai

On a standalone tub, hot tub repair happens inside the cabinet. That’s where the heater element, one or two jet pumps, sometimes a blower, and the control board live. The cabinet keeps the rain off, but in our climate it also traps heat and humidity. We open it up and check the wiring and connections. We also look for the slow drips that rot a cabinet floor before anyone notices.

How Long a Spa Should Take to Heat

It depends on the heater and the size of the spa. Heating water takes about 8.33 BTUs per gallon for each degree. So raising a 400-gallon spa 20 degrees needs roughly 67,000 BTUs. A gas heater sized for the pool delivers that quickly, and plenty of attached spas here heat with gas. The electric elements in most standalone tubs are slow, often adding only a few degrees an hour.

If your spa used to heat in a certain time and now takes noticeably longer, something changed. Usually it’s flow, scale in the heater or a failing element. It’s worth a hot tub repair call before it stops heating altogether. A good insulated cover helps too, because most of a spa’s heat escapes through the surface.

How Our Spa Repair Process Works

Every spa repair follows the same four steps, so you know the cause and the price before anything gets replaced.

Spa repair process in four steps: diagnose the fault, explain and quote, make the repair, test before we leave

First we diagnose the whole system, not just the part you noticed. A cold spa might be the heater. It might also be a clogged filter, a stuck valve or a sensor. So we check flow, power and controls before we name a part.

Then we explain what failed and why, and give you the price before we touch anything. Once you approve it, we make the repair with parts that match your equipment. Before we leave, we run the spa and check that it heats, holds temperature, pushes strong jets and isn’t leaking.

Repair or Replace Spa Equipment?

On any spa or hot tub repair, the rule is simple. If one part failed and the rest of the equipment is sound, repair it. A capacitor, seal, sensor or element costs far less than a new pump or heater. Replacement makes sense when the equipment is old or you’re patching the same unit every few months. It also makes sense when parts for an older control system are no longer made. If it’s a close call, you’ll get a price for each option.

On attached spas, the spa heater is often the pool heater too, so the choice affects both. Our pool heater installation page compares gas heaters and heat pumps. Gas makes sense on a spa if you want it hot quickly.

What Spa Repair Costs in West Palm Beach

Most spa repairs here run about $180 to $500 for parts and labor, depending on what failed. A diagnostic visit typically runs $100 to $200, and we usually put it toward the repair if you go ahead.

Bigger equipment costs more. A failed pump capacitor is usually about $150 including labor. A motor or shaft seal runs $250 to $600, and a heater repair $200 to $800. Across all equipment, most repairs land between $100 and $800.

You approve the price before we start. If the fix is a cheap part like a capacitor, gasket or sensor, that’s what you pay for.

Spa Repair Across Palm Beach County

We handle spa and hot tub repair from Jupiter to Boynton Beach, including Palm Beach Gardens, Lake Worth Beach and Greenacres. Our base is in West Palm Beach. We’re owner-operated, licensed and insured, and rated 5.0 on Google.

Spa repair is one branch of our pool equipment repair work, and part of what we do for pool service in West Palm Beach. That runs from weekly cleaning to work on the whole equipment pad. Regular spa cleaning catches most of these problems early. A slow heater or a weak jet gets noticed long before it quits.

Request a quote or call (561) 567-0822. Tell us what the spa is doing, whether it’s attached or standalone, and the brand if you know it.

Spa Repair FAQs

These are the spa and hot tub questions we hear most. Don’t see yours? Call (561) 567-0822.

Costs, Repairs and Choosing a Company

Most spa repairs at Simple Pool Care run about $180 to $500 for parts and labor. A diagnostic visit typically runs $100 to $200. Bigger jobs cost more: heater repairs run $200 to $800, and a pump motor or shaft seal $250 to $600. You approve the price before any work starts.

Repair it when one part has failed and the rest is sound. A capacitor, seal, sensor or heating element costs far less than new equipment. Replace it when the unit is old, keeps needing repairs or uses parts that are no longer made. On a close call, Simple Pool Care prices both options.

Both. Simple Pool Care repairs spas built into the pool and standalone hot tubs, from heaters and jet pumps to blowers, plumbing and topside controls. Attached spas often share the pool's pump, filter and heater, so we check the whole system first.

We pressure test the plumbing and use dye at the fittings to see exactly where water escapes. Common spots are pump shaft seals, unions, heater connections, jet bodies and plumbing under the cabinet. To confirm a leak first, mark the level with the cover on and check it after 24 hours.

Simple Pool Care is owner-run and based in West Palm Beach. We're licensed and insured, hold a 5.0 rating on Google, and our factory training covers Hayward, Pentair, Jandy and Zodiac. We diagnose before we quote and repair the failed part instead of replacing whole units by default.

Hot Tub Problems We Fix Most

Low water flow is the usual cause. A dirty filter, closed valve or air in the pump stops the flow or pressure switch from letting the heater fire. Next, check for a scaled or burned-out element, a failed sensor or a tripped high-limit switch. On attached spas, the pool heater may be at fault.

Weak jets usually mean the pump isn't getting enough water. A clogged filter or pump basket, low water or a suction air leak starves it. Other causes are a diverter valve set wrong, closed air controls, scale in the jets or a failing jet pump. Check the filter first.

A GFCI trips when it detects current leaking out of the circuit. Common causes are a shorted heater element, moisture in a pump, blower or control box, or a wiring fault. Stop resetting it and leave the spa off until it's checked, because the GFCI is preventing a shock.

It depends on use. Take the gallons, divide by 3, then divide by the number of daily users to get the days between drains. A 350-gallon spa with four regular users needs fresh water in under 30 days. Replace it sooner if total dissolved solids climb about 1,500 ppm above the fill level.

It depends on the heater and the spa's size. A gas heater warms an attached spa quickly, while the electric element in most standalone tubs adds only a few degrees an hour. If it now heats slower than it used to, check for low flow, heater scale or a failing element.

Call Us